C. Shi, R. Wang, G. Zhu, S. Qiu, J. Long
[5] I. V. Kozhevnikov, Appl. Catal., A 2003, 256, 3–18.
[6] I. V. Kozhevnikov, Catal. Rev. - Sci. Eng. 1995, 29, 311–352.
[7] M. N. Timofeeva, Appl. Catal., A 2003, 256, 19–35.
[8] T. Okuhara, Appl. Catal., A 2003, 256, 213–224.
[9] M. Misono, Chem. Commun. 2001, 1141–1152.
[10] Y. Guo, C. Hu, C. Jiang, Y. Yang, S. Jiang, X. Li, E. Wang, J.
Catal. 2003, 217, 141–151.
[11] P. A. Jalil, M. A. Al-Daous, A. A. Al-Arfaj, A. M. Al-Amer, J.
Beltramini, S. A. I. Barri, Appl. Catal., A 2001, 207, 159–171.
[12] L. R. Pizzio, P. G. Vázquez, C. V. Cáceres, M. N. Blanco, Appl.
Catal., A 2003, 256, 125–139.
FULL PAPER
measurements, the volume of adsorbed N2 was normalized to stan-
dard temperature and pressure, specific surface areas were deter-
mined from the linear part of the BET equation, the average pore
diameter was calculated by using the adsorption branches of the
N2 isotherms. Infrared (IR) spectroscopy was performed with a
Bruker IFS 66v/S infrared spectrometer in the range 400–4000 cm–1
by using KBr pellets in vacuo (Ͻ0.4 Pa) at ambient temperature.
The diffuse reflectance UV/Visible spectra for powder samples were
obtained with a Perkin–Elmer Lambda 20 UV/Visible spectrometer
equipped with an integrating sphere, and BaSO4 was used as the
internal standard. Solid-state 31P magic angle spinning nuclear
magnetic resonance (MAS NMR) spectroscopy was performed
with an Infinity Plus-400 spectrometer equipped with MAS at a
frequency of 104.26 MHz, chemical shifts were referenced to 85%
H3PO4 as an external standard.
[13] S. Mukai, T. Sugiyama, H. Tamon, Appl. Catal., A 2003, 256,
99–105.
[14] S. Damyanova, L. Dimitrov, R. Mariscal, J. Fierro, L. Petrov,
I. Sobrados, Appl. Catal., A 2003, 256, 183–197.
[15]
[16]
[17]
[18]
[19]
[20]
[21]
[22]
[23]
A. Bielánski, A. Lubanska, J. Pozniczek, A. Micek-Ilnicka,
Appl. Catal., A 2003, 256, 153–171.
H. Kosslick, G. Lischike, B. Parlitz, W. Storek, R. Fricke, Appl.
Catal., A 1999, 184, 49–60.
A. Ghanbari-Siahkali, A. Philippou, J. Dwyer, M. Anderson,
Appl. Catal., A 2000, 192, 57–69.
Catalytic Test
Catalytic Cracking of 1,3,5-Triisopropylbenzene
Catalytic cracking of 1,3,5-triisopropylbenzene was carried out by
using the pulse technique in a microreactor, and the analyses of the
catalytic products were performed by a gas chromatograph (GC-
17A, Shimadzu Co.) equipped with a flame ionization detector
(FID) with a flexible, 30-m OV-17 quartz capillary column. The
catalytic cracking was performed under the following standard con-
ditions: the reaction temperature was 250 °C (no thermal cracking);
the reaction pressure was atmospheric pressure; the mass of the
catalyst was 0.050 g; 0.2 µL of TIPB was injected for each test;
nitrogen was used as the carrier gas at a flow rate of 45 mL/min.
Y. Izumi, K. Hisano, T. Hida, Appl. Catal., A 1999, 181, 277–
282.
R. L. Augustine, S. K. Tanielyan, N. Mahata, Y. Gao, A. Zsig-
mond, H. Yang, Appl. Catal., A 2003, 256, 69–76.
H. Li, N. Perkas, Q. Li, Y. Gofer, Y. Koltypin, A. Gedanken,
Langmuir 2003, 19, 10409–10413.
Y. Guo, Y. Wang, C. Hu, Y. Wang, E. Wang, Chem. Mater.
2000, 12, 3501–3508.
K. Nowin´ska, R. Fórmaniak, W. Kaleta, A. Wacław, Appl. Ca-
tal., A 2003, 256, 115–123.
C. Shi, R. Wang, G. Zhu, S. Qiu, J. Long, Eur. J. Inorg. Chem.
2005, 4801–4807.
Esterification of Benzoic Acid with tert-Butyl alcohol
The esterification of benzoic acid with tert-butyl alcohol was per-
formed under nitrogen at 80 °C in a flask (30 mL) containing sus-
pended catalyst powder (60 mesh pass), benzoic acid (5 mmol), and
tert-butyl alcohol (10 mmol). The amount of catalyst used was
0.150 g. After vigorous agitation for 4 h, the products were ana-
lyzed with a gas chromatograph (6890N, Agilent Co.) equipped
with a flame ionization detector (FID) with a flexible, 30-m HP-5
quartz capillary column.
[24] Q. Liu, W. Wu, J. Wang, X. Ren, Y. Wang, Microporous Meso-
porous Mater. 2004, 76, 51–60.
[25] C. Shi, M. Xin, R. Wang, Y. Xie, L. Hu, L. Xu, R. Zhang, G.
Zhu, S. Qiu, Chem. J. Chin. Univ. 2005, 26, 1198–1201.
[26] L. Yang, Y. Qi, X. Yuan, J. Shen, J. Kim, J. Mol. Catal. A
2005, 229, 199–205.
[27] H. Yun, M. Kuwabara, H. Zhou, I. Honma, J. Mater. Sci.
2004, 39, 2341–2347.
[28] P. M. Rao, A. Wolfson, S. Kababya, S. Vega, M. V. Landau, J.
Catal. 2005, 232, 210–225.
Hydroxylation of 2,3,6-Trimethylphenol with H2O2
[29] C. T. Kresge, M. E. Leonowicz, W. J. Roth, J. C. Vartuli, J. S.
Beck, Nature 1992, 359, 710–712.
[30] S. S. Kim, W. Zhang, T. J. Pinnavaia, Science 1998, 282, 1302–
1305.
The hydroxylation reaction of 2,3,6-trimethylphenol with H2O2 was
performed at 80 °C in a flask (50 mL) containing suspended cata-
lyst powder (0.150 g, 60 mesh pass), acetonitrile (5 mL) as the sol-
vent, 2,3,6-trimethylphenol (0.156 mol), and H2O2 (0.052 mol), all
added at the same time followed by vigorous agitation for 2 h. The
products were analyzed with a gas chromatograph (6890N, Agilent
Co.) equipped with a flame ionization detector (FID) with a flexi-
ble, 30-m INNOWAX quartz capillary column.
[31] D. Zhao, J. Feng, Q. Huo, N. Melosh, G. H. Fredrickson, B. F.
Chmelka, G. D. Stucky, Science 1998, 279, 548–552.
[32] A. Corma, Chem. Rev. 1997, 97, 2373–2419.
[33] Y. Liu, Y. Cao, N. Yi, W. Feng, W. Dai, S. Yan, H. He, K. Fan,
J. Catal. 2004, 224, 417–428.
[34] A. Corma, A. Martinez, V. Martinez-Soria, J. Catal. 1997, 169,
480–494.
Acknowledgments
[35] T. Blasco, A. Corma, A. Martinez, P. Martinez-Escolano, J.
Catal. 1998, 177, 306–313.
[36] Q.-H. Xia, K. Hidajat, S. Kawi, J. Catal. 2002, 209, 433–444.
[37] Q.-H. Xia, K. Hidajat, S. Kawi, J. Catal. 2002, 205, 318–331.
[38] B. Bachiller-Baeza, J. A. Anderson, J. Catal. 2002, 212, 231–
239.
We are grateful for the financial support of the State Basic Re-
search Project (G2000077507) and the National Natural Science
Foundation of China (Grant No. 20101004).
[39] Q.-H. Xia, K. Hidajat, S. Kawi, Catal. Today 2001, 68, 255–
[1] A. Taguchi, F. Schüth, Microporous Mesoporous Mater. 2005,
77, 1–45.
[2] J. A. Rabo, Appl. Catal., A 2002, 229, 7–10.
262.
[40] P. M. Rao, M. V. Landau, A. Wolfson, A. M. S.-T. M. Her-
skowitz, Microporous Mesoporous Mater. 2005, 80, 43–55.
[3] S. Damyanova, L. Dimitrov, R. Mariscal, J. Fierro, L. Petrov, [41] X. Meng, Z. Sun, S. Lin, M. Yang, X. Yang, J. Sun, D. Jiang,
I. Sobrados, Appl. Catal., A 2003, 256, 183–197.
[4] J. Haber, K. Pamin, L. Matachowski, D. Mucha, Appl. Catal.,
A 2003, 256, 141–151.
F. Xiao, Appl. Catal., A 2002, 236, 17–22.
Received: March 3, 2006
Published Online: June 19, 2006
3060
www.eurjic.org
© 2006 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim
Eur. J. Inorg. Chem. 2006, 3054–3060